ADDITIVE for CLEANER (Additive Degreasing, Wetting Agent Compound)

Our Product : DIA ADDITIVE M-160 LS, Packaging ; 20Kg/Can

DIA ADDITIVE M-160 LS is a surfactant mixture which improves the cleaning efficiency of builder solutions. 

DIA ADDITIVE M-160 LS is suitable for spray cleaning at temperatures in a range between 50°C and 80°C.

Composition: nonionic surfactants and defoamer

Appearance: clear, light yellow solution
Density at 20°C: 1,01 g/cm³

Dependence of Temperature: 
- The viscosity of DIA ADDITIVE M-160 LS increases at low temperatures until it becomes solid.
- The cleaning efficiency of this product is not affected by low temperature.

Bath make up: Add the calculated amount of DIA ADDITIVE M-160 LS while stirring the preheated builder solution.

Range of Application: Concentration: 2-10 g/l or combination with DIACLEAN M-160L (1 : 4)

pH-Value: 8.5 – 9.5  in a solution of 10 g/l

For more details, please contact us :
PT. Aalen Chemicals Indonesia
Jl Pulobuaran III Blok G3,
Kawasan JIEP Pulogadung
Tlp : 021-46830522
Web : www.aalen.co.id
Blog : www.aalenchemicals.blogspot.com

Email : aalen.chemicals@gmail.com, aalen@cbn.net.id

POST TREATMENT (CHROMIUM BASED)

DIALENE 3 is a liquid, Cr6+ final rinse for Zinc and Iron phosphating on Steel, Zinc-coated and Aluminium made materials. Paint adhesion and corrosion resistance are improved through rinsing with DIALENE 3.

Passivating with DIALENE 3 gives temporary corrosion protection to sensitive surfaces after cleaning or etching. DIALENE 3 can be applied in dip or spray processes.

Reaction of passivating -- This product make an passive film in substrate.

Our Product : Dialene 3, packaging : 25Kg/Can

APPLICATION:

DIALENE 3 is used by spray or immersion; the average working parameters are:
Concentration: 0.02 to 0.1 % 
Free Acid: 0.2 to 0.6 points 
Total Acid: less than 2 
Temperature: ambient to 70°C 
Time: 15 to 45 seconds 

THE PROCESS :
The complete process for conversion coating a metal surface normally consists of the following steps:
A.  Conversion coating
B.  Water rinsing
C.  Treating with the DIALENE 3 post treatment solution
D.  Drying

DRYING
The articles treated with DIALENE 3 should be dried immediately.  Enough heat usually remains from the hot DIALENE 3 treatment to cause heavy gauge articles to dry satisfactorily.  Articles which do not dry quickly by this method should be force-dried by other means, such as with an air blow off or a drying oven.

ADVICES :
- The post treatment follows the water rinse after the conversion coating treatment solution. 
- Effort should be given to providing an adequate rinse following the conversion coating step to avoid excessive contamination of the post treatment solution.
- The higher temperatures facilitate drying, while the lower temperature reduce the tendency for staining to occur.
- A portion of the solution should be discarded continuously to prevent excessive contamination. 

For more details, please contact us :
PT. Aalen Chemicals Indonesia
Jl Pulobuaran III Blok G3,
Kawasan JIEP Pulogadung
Tlp : 021-46830522
Web : www.aalen.co.id
Blog : www.aalenchemicals.blogspot.com
Email : aalen.chemicals@gmail.com, aalen@cbn.net.id

PAINT COAGULANT (Powdered)

PAINT COAGULANT (Powdered, Alkaline)

Field of application: Paint coagulant, paint detackcifier for all solvent based paints and all normal spray booth installations

Appearance: white powder

 Our Product : Dia Spraybooth 8, packaging : 25 Kg/Bag

Shelf life: At least 1 year at room temperature and dry storage in sealed original packaging

Application:
Bath Preparation per 1000 Liters
Acrylic 0.25 to 1.2 kilograms
Alkydis 0.6 to 2.0 kilograms
Certain Alkyds and Enamels 2.5 to 3.6 kilograms

After the spray booth has been thoroughly cleaned and the system refilled with water and circulating, gradually add the required quantity of DIA SPRAYBOOTH 8 at the pump intake. After allowing several minutes for the material to dissolve, the booth is ready for operation. A short time after the paint has been sprayed into the booth, check the condition of the sludge.

If it is tacky, increase the DIA SPRAYBOOTH 8 concentration by 10% of the initial charge. Before making the addition, predissolve the material in water because there will be sludge in the booth.

Bath control:
Free Alkali, points 1 to 30
Titration of 100 ml with 0,1 N H2SO4 against Phenolphthalein
mL 0,1 N H2SO4 used is Free Alkali
.
Replenishment: An addition of 0.12 kilograms of DIA SPRAYBOOTH 8 per 1000 liters will increase the free alkali strength approximately 1 point.

Foam behavior: Some of paint components could be foamed at the alkaline pH-value. In this case there are suitable defoamers.

Waste disposal information:
Applicable regulations covering disposal and discharge of chemical should be consulted and followed. Disposal information for the chemical, in the form as supplied, is given on the Material Safety Data Sheet for the chemical.

For more details, please contact us:
PT. Aalen Chemicals Indonesia
Jl Pulobuaran III Blok G3,
Kawasan Industri JIEP, Pulogadung
Jakarta Timur
Tlp : 021-46830522
Website : www.aalen.co.id
Email : aalen.chemicals@gmail.com, aalen@cbn.net.id

ACCELERATOR

LIQUID KATALISATOR For ZINC PHOSPHATE PROCESS

DIA TONER 20 is a liquid clear compound based on Sodium Nitrite and used as additive to be added to Zinc Phosphate solutions.

Application :

DIA TONER 20 is added both at the make-up and as a replenisher to Zinc Phosphate process.

Our Technical service will suggest the best operational concentration depending on the specific situation.

ADVICES

Small differences in product appearance do not affect its performances.

Analysis Toner Gas :
a.  Fill a saccharometer with phosphating solution. No air shall be left in it.

b.  Add 1 - 2 grams of Sulfamic Acid through the opening of the saccharometer.

c.  Turn the saccharometer upside down. 

d.  As soon as Sulfamic Acid reaches its top, set the saccharometer back to the original position.

e.  Carry out this procedure quickly and pay attention not to bring back air when turning it upside down.

f.  When gas evolution is ceased, read the amount of gas generated on the scale.

g. The volume of this gas generated indicates the accelerator concentration/Toner gas (mls).

For more details, please contact us :
PT. Aalen Chemicals Indonesia
Jl Pulobuaran III Blok G3,
Kawasan JIEP Pulogadung
Tlp : 021-46830522
Web : www.aalen.co.id
Email : aalen.chemicals@gmail.com, aalen@cbn.net.id

NON AQUEOUS IRON PHOSPHATE

IRON PHOSPHATING - SOLVENT BASED

Our Product : DIAFOS SP-6000, packaging : 20 Lt/Can

Properties and application:
DIAFOS SP-6000 is a liquid product for iron phosphates.

DIAFOS SP-6000 degreases and cleans steel. On cold rolled steel and iron it simultaneously generates an uniform phosphate layer.

The phosphate layer provides an excellent adhesion for organic coatings and improves the corrosion resistance.

The Process:
A. Cleaning with DIACLEAN AC-600  (or other cleaner-water based)

B. Water rinsing

C. Dry

D. Coat with DIAFOS SP-6000

E. Dry

Note: If the work is solvent-cleaned, Operations No. B and C, above may be omitted.

  Diafos SP-6000, Packaging : 20 Lt/can

Operating conditions (Recommended conditions): Product concentration: 100%

Temperature: ambient

DIAFOS SP-6000 is applied undiluted by brushing, dipping, spraying, flow-coated, or roll-coating. 

Optimum coating weights produced by any method will normally range between 2000 and 2500 milligrams per square meter.

When spraying DIAFOS SP-6000, a uniformly wet coating should be produced; and low air gun pressure should be used to minimize overspray

For more details, please contact us :

PT. Aalen Chemicals Indonesia

Jl Pulobuaran III Blok G3,

Kawasan JIEP Pulogadung

Tlp : 021-46830522

Web : www.aalen.co.id

Email : aalen.chemicals@gmail.com, aalen@cbn.net.id

ANTI RUST (RUST PREVENTIVE OIL,PROTECTOR)

DIACOTE CR 56 is low viscocity, fast penetration rust preventive oils, designed to provide superior protection and water displacement properties, intended to be used in the protection of steel part stored indoor and coverage outdoors from rust and stain. DIACOTE CR 56 is formulated and designed for use on all metal surfaces including machined or other finished part that may corrode. 

PHYSICAL CHARACTERISTICS :

Appearance : Amber Liquid

Specific Gravity  : 0.8 - 0.9 g/L (25C)

Flash point : > 72C

Viscocity : 2.55 cSt (40C)

APPLICATION

This oil is ready to used and easy by dipping, spraying and brushing to work piece for in-process and/or finishes process.

BENEFITS : 

- Highly effective rust protection

- Long effective coating life 5 to 6 monts protection.

- Safe to used and mild odor

- Displace water from metal surface

For more details, please contact us :

PT. Aalen Chemicals Indonesia

Jl Pulobuaran III Blok G3,

Kawasan JIEP Pulogadung

Tlp : 021-46830522

Web : www.aalen.co.id

Blog : www.aalenchemicals.blogspot.com

Email : aalen.chemicals@gmail.com, aalen@cbn.net.id